Difference between revisions of "Garmin FMI"
(No difference)
|
Revision as of 18:06, 30 September 2010
Garmin's Fleet Management Interface is used by the Tracker2 and the GTRANS cable. At least two different connector types are in use by current Garmin models - a USB mini-B type and an 18-pin Hirose ST series connector. The official FMI specification does not include waypoint creation, but it does work on some models. However, most models create duplicate waypoints for a moving station, rather that simply moving the existing waypoint.
| Model | Displays Waypoints? | Displays Comment Text? |
Makes duplicates? (Not Good) |
Connector | Garmin Cable P/N |
Notes |
|---|---|---|---|---|---|---|
| nuvi 2x5 series | No | N/A | N/A | Mini-B | 010-11232-00 | |
| nuvi 350 | Yes | Yes | No | Mini-B | 010-10813-00 | Must have power through cradle, FMI connection on side of unit |
| nuvi 360 | Yes | ? | Yes | Mini-B | 010-10813-00 | Must have power through cradle, FMI connection on side of unit |
| nuvi 465T | No | N/A | N/A | Mini-B | 010-11232-00 | |
| nuvi 5xx series | No | N/A | N/A | Mini-B | 010-11232-00 | |
| nuvi 600 series | Yes | No | Yes | 18-pin | 010-10865-00 | FMI connection on cradle |
| nuvi 7x0 series | No | N/A | N/A | 18-pin | 010-10865-00 | |
| nuvi 7x5 series | No | N/A | N/A | 18-pin | 010-10865-00 | |
| nuvi 12xx series | No | N/A | N/A | Mini-B | 010-11232-00 | Minimum Software 3.60 |
| nuvi 13xx/14xx series | No | N/A | N/A | Mini-B | 010-11232-00 | Minimum Software 3.60 |
| StreetPilot 2720 | Yes | ? | Yes | Mini-B | 010-10813-00 | |
| StreetPilot 7200/7500 | Yes | Yes | Yes | Mini-B | 010-10813-00 |
For Garmin's FMI FAQ, visit http://www8.garmin.com/solutions/commercial/faq.jsp.
Contents
Comment Text
Not all Nuvis will display the comment text from APRS packets. The Nuvi 350 properly displays comments, when viewing stations from the Favorites listing.
Other Nuvis do not, for example the 680 does not display comment or status text at all. APRS objects show up as favorites, but with none of the comment or status text.
Information on other Garmin models should be added to this table.
Connectors
Mini-B
The USB Mini-B 010-10813-00 cable uses an 8.2k ohm resistor to ground on the ID pin to identify an FMI cable. The 010-11232-00 cable uses an approximately 12k ohm resistor. Serial signals are 9600 baud, 0-3.3v, inverted (0v = 1, 3.3v = 0).
| Pin 1 | +5v from PND |
| Pin 2 | Data in to PND |
| Pin 3 | Data out from PND |
| Pin 4 | ID (8.2k to ground) |
| Pin 5 | Ground |
18-Pin
The 18-pin FMI connector is a Hirose ST40X-18S-CV.
| Pin 1 | +12v to PND |
| Pin 2 | +12v to PND |
| Pin 3 | +5v from PND |
| Pin 4 | Data out from PND |
| Pin 5 | Data in to PND |
| Pin 6 | Data ground |
| Pin 7 | ID (8.2k to ground) |
| Pin 8 | Power ground |
| Pin 9 | Power ground |
Numbering is per Hirose data sheet. On the wiring side, odd numbered pins are on the top row and even numbered pins on the bottom row.
Please note that this information is preliminary and may be incomplete or inaccurate! The pinouts above were determined by disassembly of a Garmin 010-10865-00 cable and have not been tested.
